Clik here to view.
Advanced users • Re: Argon One Replacement Daemon
Plenty of changes - Pi5 and bookwormThagrol wrote some notes on bookworm: viewtopic.php?t=359026&hilit=Bookworm+v ... e#p2153199Then there is the massive Pi5 thread, which I cannot find The docs...
View ArticleSDK • Re: Wrong uID size from SDK when using IS25LP flash
Same issue for ZD25WQ16 discussed here - viewtopic.php?t=331949Statistics: Posted by hippy — Tue Feb 20, 2024 11:01 am
View ArticleGeneral • Re: Waveshare UPS-B LiPo Battery
Perhaps have a look to https://www.lithium-polymer-akkus.de/50 ... mer-akkus/ There are a few batteries on the page which could mechanically fit into the available space.Statistics: Posted by ghp —...
View ArticleGeneral discussion • Re: Hardware Fault USB
I bought a pi5 from element14Mounted in an Argon neo caseCPU temp settles at 40CDay 1 setupDay 2 no mouse, no keyboard, no USB on any portsAsked Element14 for a RAThey asked me to go to forum (to say...
View ArticleSDK • Re: Increasing USB CDC Transfer Speeds
I am not using Dual Ports, i just changed the Example to my needs. Do you have any buildable example for me for your solution, just adding the library and calling the functions doesn't...
View ArticleBeginners • Re: No "Signal Desktop" available for ARM64. No Flatpak...
https://signal.org/download/https://en.wikipedia.org/wiki/Signal_(software)Signal is an encrypted messaging service for instant messaging, voice, and video calls.[12][13] The instant messaging...
View ArticleAdvanced users • Re: Raspberry Pi 5 Overclock CPU/GPU Safety
...This brings me to my next question. Assuming that they don't get that hot even with overclocking; By placing thermal pads on them, could they get hot because of the heat transferred from SoC, PMIC...
View ArticleGeneral discussion • Re: Raspberry Pi 5 Active Cooler thermal pad alignment
They don't get hot enough to need extra cooling.When the RPI5 is overclocked, should we place extra pads on the RAM and RP1? or do they not get hot even with overclocking the SoC?This brings me to my...
View ArticleTroubleshooting • Re: Is my analysis correct? Networkmanager waiting at boot
My apologies for late respons. I have solved the problem I think. Restoring the wifi network-extender helped. But what helped most was the discovery of a service running since I installed the NVMe,...
View ArticleTroubleshooting • Re: R3B: Supplied 12V on GPIO power - what breaks?
It's possible that the MOSFET U9 itself has been damaged by the overvoltage incident.When MOSFETs get damaged, they can exhibit behaviors like increased heat dissipation. Given that the MOSFET gets...
View ArticleBeginners • Re: SPI Question
I presume you want to attach to a Pi?Statistics: Posted by jamesh — Wed Feb 21, 2024 10:52 am
View ArticleTroubleshooting • Triggerhappy failing on 65 bit Bookworm on Raspberry Pi 4B
Hello,I am testing the new Bookworm 64 bit https://downloads.raspberrypi.com/raspi ... 023-12-06/ on Raspberry Pi 4B.During boot, the triggerhappy udev rule is failing and board doesn't boot...
View ArticleInterfacing (DSI, CSI, I2C, etc.) • Re: Two different cameras on single MIPI...
Thank you!I will just give it a try and check if it is working properly. However, I will also evaluate the other possible solutions as the concept of keeping both senors permanently streaming is...
View ArticleOfficial Display • Re: Raspberry Pi 4 with official touchscreen no display...
Yes, thank you, this worked. My touches were not sensed this morning and running these two commands sorted it. I have added the following lines to my crontab to hopefully prevent this form happening...
View ArticleTroubleshooting • Re: [SOLVED] dmesg : "raspberrypi-firmware...
Hello, Is this problem solved and how?No it is not solved. I'm not sure if a mod or the OP changed the title to SOLVED, but it was premature.I get the same error in the dmesg with a rpi5 8GBIf you do...
View ArticleTroubleshooting • RPI notworking
Follow up for post viewtopic.php?t=365815 . RPi still not working.Keeping it connected to usb only red light blinking and apparently nothing is turning hot. Cant seem to find the problem. I am sure...
View ArticleGraphics, sound and multimedia • Re: SPI touchscreens working on Raspberry Pi...
There is no framebuffer display driver by default on Bookworm. That makes it difficult to use Pygame 2 with SPI displays as the latter used to use it. HDMI displays work fine with KMSDRM display...
View ArticleDevice Tree • Re: Pi5 - overlay for enabling 3 SPI interfaces and using RP1...
Or do I need one such definition for each PWM signal?You can group multiple GPIOs that have the same settings, or keep them separate - it's flexible. But shouldn't that the part of rp1.dtsi?I don't...
View ArticleC/C++ • Re: is there any instuction how to install ecilpse
That command only downloads (an old version of) the Eclipse package to your current directory. The official install guide is here: https://wiki.eclipse.org/Eclipse/Installation. The current version of...
View ArticleTroubleshooting • Re: Trying to install DUC (noir.com) but getting...
If you are staying on Bullseye for now you may find https://ddclient.net/ could do the job for you.Statistics: Posted by MiscBits — Thu Feb 22, 2024 10:50 am
View Article